Index     FAQ      Search

It is currently Sat Jan 20, 2018 12:48 am




Reply to topic  [ 1 post ] 
 Rover 827 V6 Technical data 
Author Message
 Post subject: Rover 827 V6 Technical data
PostPosted: Thu Apr 06, 2006 8:24 pm 
Bronze Trader

User avatar
Bronze Trader

Joined:
Sat Aug 09, 2003 7:02 pm
Posts:
11309
Location:
Norwich
VEHICLE IDENTIFICATION
Engine code V6-2,7

Number of cylinders: 6/OHC
Capacity cm3: 2675
Output:kw (din hp) RPM:::: 124 (169) 5900

Ignition system Description: MAP-i
Trigger location: distributer,crankshaft

Fuel system:
Make: honda
Type: PGM-Fi
Description: MFI-s

Air metering Type: MAP


TUNEING AND EMISSIONS


Fireing order: 1-4-2-5-3-6

Ignition timeing BTDC: Engine/rpm 15+2/680

Idle speed rpm: 680+50

Oil temp for CO test degrees C : 70

CO content at idle tail pipe Vol.% : 0,1 Max

CO2/O2 content at idle speed Vol.%: 14,5-16/0,1-0,5

HC content at idle speed ppm: 100

Oil presure Bar/rpm: 3.4 min/3000

Radiator cap Bar: 1

Thermostat opens degrees C : 78

LUBRICANTS AND CAPACITIES

Engine oil Grade: SAE 10W/40
Alternative: SAE 10W/30

Engine capacity with filter: 4.5 litres

Gearbox oil grade: SAE 10W/40
Gearbox fluid capacity : 2.3 litres

Automatic fluid: Dexron ll
Automatic fluid capacity: 3.2 litres

Brake fluid Type: DOT 4


Power steering fluid Type: Dexron ll
Power steering fluid capacity: 1.3 litres

FUEL SYSTEM
Fuel pump delivery presuer BAR: 4.1
System presure without vacume BAR: 2.5
Regulated presure with vacume BAR : 2


TIGHTNING TORQUES
Cylinder head

Stage1: 40 NM
Stage2: 50 NM
Stage3: 68 NM

Tightning sequence

CAM PULLY END (7) (3) (1) (5)
CAM PULLY END (8 ) (4) (2) (6)

CAM PULLY END (8 ) (4) (2) (6)
CAM PULLY END (7) (3) (1) (5)


Main bearings Tighten bolts as follows:

Bolts 1-8 = 41 NM
Bolts 9-16 =68NM
Bolts 17-24 = 50 NM

Bolt order
(17)..(19)..(21)..(23)
(1).....(3)....(5)....(7)
(14)..(10)...(12)..(16)

(13)...(9)....(11)...(15)
(2)....(4)....(6).....(8 )
(18 )...(20)..(22)...(24)



Big end bearings:
Stage 1: 20 NM
Stage 2: 50 NM

Sump bolts: 12 NM

Sump drain bolt: 45 NM

Flywheel/Driveplate: 105 NM / 75 NM

Clutch to flywheel: 26 NM

Crankshaft pully / damper: 115 NM

Camshaft sprocket / gear: 32 NM

Inlet manifold to cylinder head: 22 NM

Exhaust manifold to cylinder head: 45 NM

Spark plugs: 27 NM

Oxygen sensor (lambda) : 45 NM



Front hub: use new nut and tighten to 415 NM

Rear hub: Use new nut and tighten to 245 NM

Steering rack to rod end: 44 NM

Brake caliper to carrier FRONT: 33 NM

Brake caliper carrier to hub FRONT : 75 NM

Brake caliper to carrier REAR : 33 NM

Brake caliper carrier to hub REAR: 45 NM

Road wheels: 110 NM

Hope this helps :mrgreen:


Last edited by Marty on Thu Apr 06, 2006 8:45 pm, edited 1 time in total.

Offline
  Profile Feedback  
 
Display posts from previous:  Sort by  
Reply to topic  [ 1 post ] 


 Who is online 

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  

 
Index  |  FAQ  |  Search

Content © Rovertech - Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group